Page 47 - APPLIED PROCESS DESIGN FOR CHEMICAL AND PETROCHEMICAL PLANTS, Volume 1, 3rd Edition

32 Applied Process Design for Chemical and Petrochemical Plants

Hazardous Locations 497 • Chapter V Preparation of Equipment for Safe Entry
Explosion Prevention Systems 69 and Work
Explosion Venting 68 • Chapter VI Pressure Vessels (Tower, Drums, and
Explosive Materials, Code for 495 Reactors)
Fire Hazards of Materials, Identification 704 • Chapter VII Heat Exchangers, Condensers, and Cool-
Fire Pumps, Centrifugal 20
Fire Pumps, Steam 21 er Boxes
Flammable and Combustible Liquids, Class. 321 • Chapter IX Fired/Heaters and Stacks
Flammable and Combustible Liquids Code 30 • Chapter IXX Atmospheric and Low Pressure Storage
Flammable and Combustible Liquids, Tanks
Farm Storage of 395 • Chapter XIX Inspection for Accident Prevention
Flammable and Combustible Liquids, • Chapter XX Inspection for Fire Protection
Portable Shipping Tanks 386 • Std. 620 Recommended Rules for Design and Con-
Flammable and Combustible Liquids, struction of Large, Welded, Low Pressure Storage
Tank Vehicles for 385
Tanks
• RP-2003 Recommend Practice for Protection Against
Standards and Recommended Practices of American Ignitions Arising Out of Static, Lightning and Stray
Petroleum Institute: Currents
• 2521 Use of Pressure-Vacuum Vent Valves for Atmos-
• 520 Design and Installation of Pressure-Relieving Sys- pheric Pressure Tanks to Reduce Evaporation Loss
tems in Refineries • 2523 Petrochemical Evaporation Loss from Storage
Part I Design Tanks
Part II Installation
• 521 Guide for Pressure Relief of Depressuring Systems Steel Structures Painting Council, Ref. SSPC-Vis 1-67
• 525 Testing Procedures for Pressure Relieving
Devices Discharging Against Variable Back Pressure • No. 1 "Pictorial Surface Preparation Standards for
• 526 Flanged Steel Safety Relief Valves for Use in Painting Steel Structures
Petroleum Refineries
• 527 Commercial Seat Tightness of Safety Relief Occupational Safety and Health Administration
Valves with Metal-to-Metal Seats (OSHA) Regulations Environmental Protection Agency
• 540 Recommended Practice for Electrical Installa- (EPA Regulatory section)
tions in Petroleum Refineries Metals Handbook, ASM International
• 550 Installation of Refinery Instruments and Control
Systems • Volume l Properties and Selection: Irons and Steels
Part I Process Instrumentation Control (Latest Ed.)
Part II Process Stream Analyzers
• 1101 Measurement of Petroleum Liquid Hydro- • Volume 2 Properties and Selection: Nonferrous
Alloys and Pure Metals (Latest Ed.)
carbons by Positive Displacement Meter
• 2000 Venting Atmospheric and Low Pressure Storage • Volume 4 Heat Treating(l981)
• Volume 8 Mechanical Testing (1985)
tanks (Non-refrigerated and Refrigerated)
• 2545 Method of Gauging Petroleum and Petroleum • Volume 9 Metallography and Microstructures (1985)
Products • Volume 11 Failure Analysis and Prevention ( 1986)
• 2217 Guidelines for Confined Space Work in the • Volume 13 Corrosion (Latest Ed.)
Petroleum Industry • Volume 17 Nondestruction Evaluation and Quality
• 2513 Evaporation Loss in the Petroleum Industry- Control (1989)
Causes and Control
• 2516 Evaporation Loss from Low-Pressure Tanks Instrument Society of America, Standards and Practices
• 2517 Evaporation Loss from External Floating Roof
Tanks • RPl.1-7 Thermocouples and Thermocouple Exten-
• 2518 Evaporation Loss from Fixed-Roof Tanks sion Wires
• Chapter II Guide for Inspection of Refinery Equip- • RP3.1 Flowmeter Installations. Seal and Condensate
ment-Conditions Causing Deterioration or Failures Chambers
• Chapter IV Guide for Inspection of Refinery Equip- • RP3.2 Flange Mounted Sharp Edged Orifice Plates
ment-Inspection Tools for Flow Measurement