Page 336 - 2018 Master Catalog

HIGH-TEMP UNDER
HEADER LOOM KIT
Designed for routing wires under headers on old and new
FOUR HOLE SPARK PLUG style Small Block Chevy engines.
WIRE LOOM KITS PART NO. DESCRIPTION
Includes two chrome plated brackets and two 4-hole looms.
72195 Black, 7-9mm
PART NO. DESCRIPTION
72180 Blue, 7-9mm DURAFIRE DISTRIBUTORS
72181 Red, 7-9mm
72183 Black, 7-9mm • Improved weight and advance cam pin retention by
TIG welding the pin backside to prevent them from
coming loose
SPARK PLUG • Upgraded strength of the plastic wire harness plug
WIRE SEPARATORS so that the two lock tabs do not break off when
Protect against heat damage by preventing contact unplugging the harness from the distributor cap
with hot engine components. PART NO. DESCRIPTION
PART NO. DESCRIPTION
72231 DuraFire Distributor - GM HEI, V8 - w/out Vacuum Advance
72160 Blue, 7-9mm
72161 Red, 7-9mm
72162 Yellow, 7-9mm ADVANCE CURVE KITS
72163 Black, 7-9mm
73163 Black, 11mm or sleeved wire • “Recurve” your distributor for full spark advance at the optimum RPM
• 3 sets of advance springs allow you to adjust the rate of spark advance
PART NO. DESCRIPTION
DISTRIBUTOR HEI Advance Curve Kit, special design centerplate eliminates over-centering of
ACCESSORIES 72300 the centrifugal weights. Fits all GM HEI Distributors
PART NO. DESCRIPTION 72310 Advance Curve Kit. Fits all 1957-75 GM/Delco Non-HEI

97860 Rotor, Distributor, Short Drive Lug. Fits Jesel, Mallory REMOTE COIL MOUNTING
26140 Distributor Gear Shim Kit - (2) .010” shims, (2) .020” shims, (1) .053” shim BRACKET KIT - LS SERIES
26150 Distributor Housing Shim Kit, 1.290 I.D. & 1.830 O.D.
26200 Distributor Hold Down Clamp. Fits all V8 and 90° V6 Chevy engines, Clear-Zinc • Relocates ignition coils from valve cover
26210 Distributor Hold Down Clamp. Fits all V8 and 90° V6 Chevy engines, Chromed • Fits O.E.M. and larger aftermarket coils
with 2-9/16” bolt spacing
PART NO. DESCRIPTION
CRANK TRIGGER ULTRA
SERIES KIT 72395 Remote Coil Mounting Bracket with Spacers - LS Series
Fits O.E.M., Fluidampr, ATI, Fischer, and other BBC 8.0” or
smaller diameter damper cases with 4.749” mounting registers. BATTERY CABLE TERMINAL KITS
PART NO. DESCRIPTION Compression-style fittings with tin plated brass for added
conductivity and corrosion resistance provide solid electrical connection.
60008 Big Block Chevy - Passenger
PART NO. DESCRIPTION
74170 Battery Cable Remote Fitting End Kit, Compression-style, 3/8” opening
TIMING POINTERS 74173 Battery Cable Terminal, Copper, Solder, 3/8” diameter stud
74175 Battery Post Terminal End Kit
PART NO. DESCRIPTION
60110 SBC - 6.750” BATTERY CABLE
60125 SBC - 8” DISCONNECT SWITCH
60140 BBC - 7.250”
• One turn of the knob disconnects the battery and
saves the solid state voltage regulator and alternator
when charging
SEALED BATTERY BOX • Also deters possible car thieves when parked
Ideal for relocating a battery to the rear of any race, • Switch is rated at 100 amps for 12 or 24 DC use
street, or show vehicle with or without a rear firewall. PART NO. DESCRIPTION
PART NO. DESCRIPTION
74103 Top Terminal
74051 Sealed Battery Box, Black 74104 Side Post
336